Samsung Galaxy J2 : Flash Stock Rom Odin Method

Guide To Flash Update Samsung Galaxy J2 Lollipop 5.1.1 J200H J200F J200G J200M J200GU J200Y Odin Method Tested Firmware, Free Regional Firmwares Ready To Be Downloaded.

Important Things To Do Before Flashing Stock ROM:

      Before you can proceed to the process make sure that you do the things we will list below and that you read it carefully, this procedure works perfectly and tested by many users, so if you have doubt or questions about this post you can leave a comment below:

• Prepare your USB Cable, PC, STOCK ROM or Firmware Files (Download Below). 
• Flashing the Stock Firmware will delete your personal data from the device. If in case you are going to Flash the above firmware then take a backup of your personal data, so that you can recover your personal data if any thing wrong happens.
• Also doing this process is crucial so we admit you have a presence of mind, common sense, and read our disclaimer below, as well as make sure you have at least 60% to 80%.

Why Need Stock Firmware?

• Flashing Stock ROM will downgrade your phone if you don’t like the new update. 
• Flashing Stock ROM will Upgrade your phone. 
• Flashing Stock ROM will fix bootloop issues. 
• Flashing Stock ROM will completely Unroot . 
• Installing Stock ROM will Unbrick. 
• Flashing Stock ROM will help to Revert back to Original Stock ROM Firmware or Factory state (Helpful if you are facing force close error or any other lags or unstable internet connection).

Before starting the flashing process of this new update you need to read the following guidelines:

• Use this tutorial only with the Samsung J2 models.
• do not use the tutorial for other different models.
• download Samsung Smart Switch here in order to get latest Samsung drivers.
• the usb drivers will allow your PC to detect the phone when these two are connected.
• Also, any custom Recovery you might have installed is going to be replaced with stock Recovery image.
• you can flash the new official Lollipop firmware over custom ROMs, too, but you will have to Factory Reset the device after the update is done.
• the Factory Reset will wipe clean system partition, it removes the custom ROM, but it won’t delete any files from internal storage.
• Factory Reset process steps are listed at the end of this post.
• If the phone is running 100% official Android firmware, then you can continue straight to the next part of this post.
• this tutorial needs to be used by advanced users, we cannot be blamed in case you brick the phone nor in case you lose any data in the process.
• read whole post and do not skip any steps.

DOWNLOAD AREA:
*Samsung J200H Lollipop 5.1.1 firmware 4 files: From Here

(warning: for the j200h model dont flash BL, just flash the AP, CP, CSC)

*Samsung J200F Lollipop 5.1.1 firmware safe flash: From Here

*Samsung J200G Lollipop 5.1.1 firmware safe flash: From Here

*Samsung J200GU Lollipop 5.1.1 firmware safe flash: From Here
*Samsung J200M Lollipop 5.1.1 firmware safe flash: From Here
*Samsung J200Y Lollipop 5.1.1 firmware safe flash: From Here


Download Latest Odin Version 3.12 From Here.

Install Smart Switch for install latest samsung drivers from here.

How to Firmware for your Samsung J2?, fellow video bellow:

🔻🔻🔻🔻

How to Flash Samsung Galaxy J2:

Step 1: Download the Odin software and the J2 Prime firmware for your set , See downloads section above. 

Step 2: Extract Android firmware file.

Step 3: Extract Odin file.

Step 4: Switch off your Galaxy J2 from PC, boot it into download mode. To achieve this, wait for six to seven seconds after screen goes off, and long press Volume Down + Power + Home buttons until warning screen is displayed. Then press, Volume Up to proceed to download mode.

Step 5: Interface your phone to PC using USB cable. In Odin you should see an "Added" message appearing in the Log box at the bottom left, and the first box under ID:COM will also change its background colour to Blue.

Step 6: Load firmware into Odin. To achieve this, Click on the AP button on Odin and the select the .tar.md5 extracted file as explained in Step 3.

Step 7: Within Odin, check to ensure that Re-partition checkbox is deselected,

Step 8: Within Odin, select Start Button to start flashing the firmware on your tablet.

Step 9: After completion of installation, your Galaxy J2 will reboot automatically. You'll get a "Pass" message upon successful installation from Odin.

Step 10: Disconnect your tablet from the computer. Navigate to Settings > About Device to verify installation of new firmware.