Guide To Flash Huawei X6S Clone MT6580__X6s__X6s__w825_644_ax_xm_x6s__5.1__w825_644_ax_xm_x6s_v1.3
Navigation

Guide To Flash Huawei X6S Clone MT6580__X6s__X6s__w825_644_ax_xm_x6s__5.1__w825_644_ax_xm_x6s_v1.3

HUAWEI X6S CLONE MT6580
TESTED FIRMWARE
 FREE DOWNLOAD
EXCLUSIVE IS FOR FREE NOW

Guide To Flash Huawei X6S Clone MT6580__X6s__X6s__w825_644_ax_xm_x6s__5.1__w825_644_ax_xm_x6s_v1.3

INFO:
Brand : X6s
ProdName : full_w825_644_ax_xm_x6s
ProdModel : X6s
Device : w825_644_ax_xm_x6s
AndroidVer: 5.1
MTKxCPU : MT6580
MTKxPRJ : w825_644_ax_xm_x6s_v1.3

MT6580__X6s__X6s__w825_644_ax_xm_x6s__5.1__w825_644_ax_xm_x6s_v1.3

PRE-REQUISITE
  • This is for X6S Clone  only.
  • Your device must have 70% Of battery.
  • You need a Laptop or PC to perform this Action.
  • Download the right firmware for X6S Clone from the link bellow.
  • Make sure you have followed the steps properly. Don’t Skip and Read!
  • We are not responsible for any damage that you make to your Phone.


WHY YOU NEED TO FLASH YOUR PHONE!!
You need this firmware/stock rom if you have encountered this kind of problem in your Smartphone Listed Below:
1.Hang on logo.
2.Rebooting.
3.Bootloop & Dead boot after a wrong software.
4-Virus & Sexual Apps.
5-System crashing


How to know if the phone had a hard problem (Emmc problem)??
  • What is Emmc problem? also called read mode only,  it means that your internal memory doesnt accept command, so the phone stay on the same condition after a software or a hard reset.
  •  if the phone hang on logo after flash, you ara facing Emmc problem.
  • As a precaution you shouldn't change setting in SP flashtool from Download only to format+download, you will end with a dead phone if you have a Emmc problem ofcourse.


DOWNLOAD AREA:
Firmware Download Link:  FROM HERE OR FROM HERE 
Password For Firmware: www.freemobilefirmware.com
SP Flashtool Downloadlink: SPFlashTool 5.1628
Drivers Download Link: Mobile Mtk Drivers

REMARQUE:
MAKE BACKUP BEFORE FLASH


How To Flash Via SP FLASHTOOL?

1-Requirements:
    • A Computer PC Run Windows XP or above
    • Usb data cable (not a generic cable)
    • Mtk usb drivers installed manually, you will find instruction bellow
    • Your Mtk Smartphone Face a soft issue
    • Original stock rom (you can find it above in download section)
    • The latest SP Flashtool version

    2-How to install VCOM Drivers:
    • Open device manager from my PC or my computer.
    • Click on any item and go to actions > Add legacy hardware
    • Now, press next and select install drivers manually
    • Press next and click on have disk
    • from the browse option, select VCOM drivers From mtk drivers folder
    • Once its done. You will see a screen similar to this:




    • Once you are done with the driver installation, go to device manager > Ports (COM&LPT) you will find a device similar to this:



    3-How to flash rom using SP Flashtool?:

    • Power the phone off, remove the battery from the smartphone and put it back without booting the phone (if the battery is inside then simply switch it off).
    • Launch SP Flashtool 

    *Double clicks onFlash_tool.exe
                                           *Press OK






    • Click on scatter-loading option and browse to the scatter file of your stock rom choose MTxxxx_android.txt (scatter.txt).




    • Dont touch any options, Keep the original setting (In case you want to format device before flash press choose format+download but it'snt recommanded because you will be ended with an EMEI null)
    • If you phone is alive and has a software issue (contain virus, Stuck on logo, apps setting problem, blink, or not work as expected) I advise you to Uncheck Preloader as a precaution. On contarary check all pertitions if you have a boot problem (you phone does'nt boot when you try to power on it).
                                   

    • Once you are done with everything, click on the download button at the top of the software.



    Stop should now be prominent while other options should be grayed out


    • Connect your switched off phone with battery inside to PC via Usb cable
    • A progressbar should start running


    • In the end of an success flash process, a box should show up with green OK symbol inside


    • Disconnect the phone, remove the battery, slot it back in then power the phone.

ENJOY.
https://mega.nz/#!tIUXBJTb!UyyCLqr0rRmzxY35y-ZKIg7fBoPG05UwDMvh9wr5cHM
https://mega.nz/#!tIUXBJTb!UyyCLqr0rRmzxY35y-ZKIg7fBoPG05UwDMvh9wr5cHM

                                      
Share