INFINIX HOT NOTE X551 CLONE MT6572 ANDROID 5.1 TESTED FIRMWARE FREE DOWNLOAD
INFO:
CPU: MT6572 SW:0000 Ver: CA01
Downloading Boot8 ...
EMMC Size: 0x00E2C00000
Flash Type: EMMC
INT/EXT RAM Size: 0x0+0x0
Reading infr(EMMC)...
id:EKK_0000_V1.0
version:5.1
model:M280
PRELOADER BaseAddr:0x0 Size:0x600000
MBR BaseAddr:0x600000 Size:0x80000
EBR1 BaseAddr:0x680000 Size:0x80000
PRO_INFO BaseAddr:0x700000 Size:0x300000
NVRAM BaseAddr:0xA00000 Size:0x500000
PROTECT_F BaseAddr:0xF00000 Size:0xA00000
PROTECT_S BaseAddr:0x1900000 Size:0xA00000
SECCFG BaseAddr:0x2300000 Size:0x20000
UBOOT BaseAddr:0x2320000 Size:0x60000
BOOTIMG BaseAddr:0x2380000 Size:0x600000
RECOVERY BaseAddr:0x2980000 Size:0x600000
SEC_RO BaseAddr:0x2F80000 Size:0x40000
MISC BaseAddr:0x2FC0000 Size:0x80000
LOGO BaseAddr:0x3040000 Size:0x300000
EXPDB BaseAddr:0x3340000 Size:0xA00000
ANDROID BaseAddr:0x3D40000 Size:0x4B000000
CACHE BaseAddr:0x4ED40000 Size:0xE200000
USRDATA BaseAddr:0x5CF40000 Size:0x52C00000
FAT BaseAddr:0xAFB40000 Size:0x31FE0000
BMTPOOL BaseAddr:0xFFFF0000 Size:0x1500000
BaseAddr:0x0 Size:0x0
>>Done.
PRE-REQUISITE
- This is for Infinix X551 only.
- Your device must have 70% Of battery.
- You need a Laptop or PC to perform this Action.
- Download the right firmware for X551 from the link bellow.
- Make sure you have followed the steps properly. Don’t Skip and Read!
- We are not responsible for any damage that you make to your Phone.
WHY YOU NEED TO FLASH YOUR PHONE!!
You need this firmware/stock rom if you have encountered this kind of problem in your Smartphone Listed Below:
1.Hang on logo.
2.Rebooting.
3.Bootloop & Dead boot after a wrong software.
4-Virus & Sexual Apps.
5-System crashing
2.Rebooting.
3.Bootloop & Dead boot after a wrong software.
4-Virus & Sexual Apps.
5-System crashing
How to know if the phone had a hard problem (Emmc problem)??
- What is Emmc problem? also called read mode only, it means that your internal memory doesnt accept command, so the phone stay on the same condition after a software or a hard reset.
- if the phone hang on logo after flash, you ara facing Emmc problem.
- As a precaution you shouldn't change setting in SP flashtool from Download only to format+download, you will end with a dead phone if you have a Emmc problem ofcourse.
DOWNLOAD AREA:
FIRMWARE DOWNLOAD LINK:
PASSWORD:
password if applicable: ahmedtag
REMARQUE:
MAKE BACKUP BEFORE FLASH
How To Flash Via SP FLASHTOOL?
1-Requirements:
- A Computer PC Run Windows XP or above
- Usb data cable (not a generic cable)
- Mtk usb drivers installed manually, you will find instruction bellow
- Your Mtk Smartphone Face a soft issue
- Original stock rom (you can find it above in download section)
- The latest SP Flashtool version
2-How to install VCOM Drivers:- Open device manager from my PC or my computer.
- Click on any item and go to actions > Add legacy hardware
- Now, press next and select install drivers manually
- Press next and click on have disk
- from the browse option, select VCOM drivers From mtk drivers folder
- Once its done. You will see a screen similar to this:
- Once you are done with the driver installation, go to device manager > Ports (COM&LPT) you will find a device similar to this:
3-How to flash rom using SP Flashtool?:- Power the phone off, remove the battery from the smartphone and put it back without booting the phone (if the battery is inside then simply switch it off).
- Launch SP Flashtool
*Double clicks onFlash_tool.exe
*Press OK
- Click on scatter-loading option and browse to the scatter file of your stock rom choose MTxxxx_android.txt (scatter.txt).
- Dont touch any options, Keep the original setting (In case you want to format device before flash press choose format+download but it'snt recommanded because you will be ended with an EMEI null)
- If you phone is alive and has a software issue (contain virus, Stuck on logo, apps setting problem, blink, or not work as expected) I advise you to Uncheck Preloader as a precaution. On contarary check all pertitions if you have a boot problem (you phone does'nt boot when you try to power on it).
- Once you are done with everything, click on the download button at the top of the software.
Stop should now be prominent while other options should be grayed out- Connect your switched off phone with battery inside to PC via Usb cable
- A progressbar should start running
- In the end of an success flash process, a box should show up with green OK symbol inside
- Disconnect the phone, remove the battery, slot it back in then power the phone.
ENJOY.
