Guide To Flash G-Tide S3 Kitkat 4.4.2 Flashtool Free Method Tested Firmware
Navigation

Guide To Flash G-Tide S3 Kitkat 4.4.2 Flashtool Free Method Tested Firmware

GUIDE TO FLASH G-TIDE S3 KITKAT 4.4.2 FREE FIRMWARE DOWNLOAD


PRE-REQUISITE
This is for G-Tide S3.

*Your device must have 70% Of battery.
*You need a Laptop or PC to perform this Action.
*Download the right firmware for G-Tide S3 from the link bellow.
*Back Up your Data to make sure you have data’s in case if something Wrong
(This Process won’t loose your data)
*Make sure you have followed the steps properly. Don’t Skip and Read!
 * We are not responsible for any damage that you make to your Phone.


WHY YOU NEED TO FLASH YOUR PHONE!!
You need this firmware/stock rom if you have encountered this kind of problem in your Smartphone Listed Below:
1.Hang in logo
2.Rebooting
3.Bootloop
4-Virus Apps
5-Deadboot Recovery

Remarque: 
All needed partitions are there.
*Avoid to flash Boot files & Preloader if your phone is not dead
check only system, userdata, cache & unckeck other files.

*If you have deadboot or bootloop check all files.

How to know if the phone had a hard problem (Emmc problem)??
if the phone hang on logo after flash.
with the firmware file given you will avoid deadboot


DOWLOAD FIRMWARE:  FROM HERE
SP Flashtool Downloadlink: SPFlashTool 5.1628
Drivers Download Link: Mobile Mtk Drivers



How To Flash Via SP FLASHTOOL?


1-Requirements:
    • A Computer PC Run Windows XP or above
    • Usb data cable (not a generic cable)
    • Mtk usb drivers installed manually, you will find instruction bellow
    • Your Mtk Smartphone Face a soft issue
    • Original stock rom (you can find it above in download section)
    • The latest SP Flashtool version

    2-How to install VCOM Drivers:
    • Open device manager from my PC or my computer.
    • Click on any item and go to actions > Add legacy hardware
    • Now, press next and select install drivers manually
    • Press next and click on have disk
    • from the browse option, select VCOM drivers From mtk drivers folder
    • Once its done. You will see a screen similar to this:




    • Once you are done with the driver installation, go to device manager > Ports (COM&LPT) you will find a device similar to this:



    3-How to flash rom using SP Flashtool?:

    • Power the phone off, remove the battery from the smartphone and put it back without booting the phone (if the battery is inside then simply switch it off).
    • Launch SP Flashtool 

    *Double clicks onFlash_tool.exe
                                           *Press OK






    • Click on scatter-loading option and browse to the scatter file of your stock rom choose MTxxxx_android.txt (scatter.txt).




    • Dont touch any options, Keep the original setting (In case you want to format device before flash press choose format+download but it'snt recommanded because you will be ended with an EMEI null)
    • If you phone is alive and has a software issue (contain virus, Stuck on logo, apps setting problem, blink, or not work as expected) I advise you to Uncheck Preloader as a precaution. On contarary check all pertitions if you have a boot problem (you phone does'nt boot when you try to power on it).
                                   

    • Once you are done with everything, click on the download button at the top of the software.



    Stop should now be prominent while other options should be grayed out


    • Connect your switched off phone with battery inside to PC via Usb cable
    • A progressbar should start running


    • In the end of an success flash process, a box should show up with green OK symbol inside


    • Disconnect the phone, remove the battery, slot it back in then power the phone.



ENJOY.
                                      
Share