Guide to flash Alcatel PIXI4 4034F MT6580 Marshmallow 6.0 Tested method Free via flashtool
Navigation

Guide to flash Alcatel PIXI4 4034F MT6580 Marshmallow 6.0 Tested method Free via flashtool

GUIDE TO FLASH ALCATEL PIXI 4 4034F MARSHMALLOW 6.0 FREE FIRMWARE DOWNLOAD




PRE-REQUISITE
This is for Alcatel PIXI4 4034F.
*Your device must have 70% Of battery.
*You need a Laptop or PC to perform this Action.
*Download the right firmware for Pixi4 from the link bellow.
*Back Up your Data to make sure you have data’s in case if something Wrong
(This Process won’t loose your data)
*Make sure you have followed the steps properly. Don’t Skip and Read!
 * We are not responsible for any damage that you make to your Phone.


WHY YOU NEED TO FLASH YOUR PHONE!!
You need this firmware/stock rom if you have encountered this kind of problem in your Smartphone Listed Below:

1.Hang in logo
2.Rebooting
3.Bootloop

4-Virus Apps

5-Deadboot Recovery
6-Frp (Factory Reset Protection) 

Remarque: For Frp unlock use format+download instead download only
All needed partitions are there.
*Avoid to flash Boot files & Preloader if your phone is not dead
check only system, userdata, cache & unckeck other files.

*If you have deadboot or bootloop check all files.

How to know if the phone had a hard problem (Emmc problem)??
if the phone hang on logo after flash.
with the firmware file given you will avoid deadboot
INFO:
Wait for phone...
Phone found! [ 24 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6580
BB_CPU_NME : [MediaTek] MT6580_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x94
NAND Flash : NOT INSTALLED
eMMC Flash : 11010030303847373000C99549CE63D5
Initialize Memory ... 
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x11 , OEM : 0100
[eMMC] : FLASH_INF : [TOSHIBA] , 07G80
[eMMC] : FLASH_CID : 11010030303847373000C99549CE63D5
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000001D2000000
[eMMC] : FLASH_UCP : 7456 MiB [eMMC 8 GiB]
DEV RID    : 0xECD5AB9A7DF4F037F6AD92BCE8E470EC
INT RAM    : 0x00020000
EXT RAM    : 0x40000000 [1 GiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Reading Flash Content now ... 

xGPT : Normalize settings Ok!


[Read Ok] : preloader_pixi4_4_8g1g.bin
[Read Ok] : lk.bin
[Read Ok] : logo.bin
[Read Ok] : boot.img
[Read Ok] : recovery.img
[Read Ok] : secro.img
[Read Ok] : system.img
[Read Ok] : cache.img
[Read Ok] : userdata.img

[ScatCFG] : MT6580 / V1.1.2 / pixi4_4_8g1g / EMMC
Android Info saved
HWConfig Info saved
FW Size : 1731 MiB
Scatter saved to : C:\Users\RAWANE\Desktop\MT6580______\

DOWNLOAD AREA:
Firmware Download Link: FROM HERE
Password For Firmware: www.dzgsm.com

SP Flashtool Downloadlink: SPFlashTool 5.1628
Drivers Download Link: Mobile Mtk Drivers     


*This Firmware partitions is all you need to repair the phone software problems


Fellow Video Instructions:
↧↧↧
Same Method as Doogee X6 Marsmallow 6.0
⧭⧭⧭⧭
How To Flash Via SP FLASHTOOL?
    • A Computer PC Run Windows XP or above
    • Usb data cable (not a generic cable)
    • Mtk usb drivers installed manually, you will find instruction bellow
    • Your Mtk Smartphone Face a soft issue
    • Original stock rom (you can find it above in download section)
    • The latest SP Flashtool version

    2-How to install VCOM Drivers:
    • Open device manager from my PC or my computer.
    • Click on any item and go to actions > Add legacy hardware
    • Now, press next and select install drivers manually
    • Press next and click on have disk
    • from the browse option, select VCOM drivers From mtk drivers folder
    • Once its done. You will see a screen similar to this:




    • Once you are done with the driver installation, go to device manager > Ports (COM&LPT) you will find a device similar to this:



    3-How to flash rom using SP Flashtool?:

    • Power the phone off, remove the battery from the smartphone and put it back without booting the phone (if the battery is inside then simply switch it off).
    • Launch SP Flashtool 

    *Double clicks onFlash_tool.exe
                                           *Press OK






    • Click on scatter-loading option and browse to the scatter file of your stock rom choose MTxxxx_android.txt (scatter.txt).




    • Dont touch any options, Keep the original setting (In case you want to format device before flash press choose format+download but it'snt recommanded because you will be ended with an EMEI null)
    • If you phone is alive and has a software issue (contain virus, Stuck on logo, apps setting problem, blink, or not work as expected) I advise you to Uncheck Preloader as a precaution. On contarary check all pertitions if you have a boot problem (you phone does'nt boot when you try to power on it).
                                   

    • Once you are done with everything, click on the download button at the top of the software.



    Stop should now be prominent while other options should be grayed out


    • Connect your switched off phone with battery inside to PC via Usb cable
    • A progressbar should start running


    • In the end of an success flash process, a box should show up with green OK symbol inside


    • Disconnect the phone, remove the battery, slot it back in then power the phone.

ENJOY.
                                      
Share