SAMSUNG GALAXY S7 EDGE CLONE SM-G935F MT6580 CLONE FIRMWARE FREE DOWNLOAD
INFO:
Wait for phone...
Phone found! [ 34 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6580
BB_CPU_NME : [MediaTek] MT6580_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x94
NAND Flash : NOT INSTALLED
eMMC Flash : 150100463732324D42000FDA6A67A327
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BM227
[eMMC] : FLASH_CID : 150100463732324D42000FDA6A67A327
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00080000
[eMMC] : FLASH_LEN : 0x00000001D2000000
[eMMC] : FLASH_UCP : 7456 MiB [eMMC 8 GiB]
DEV RID : 0xE5974B4A1D80C859CB1BE3809CCF2E75
INT RAM : 0x00020000
EXT RAM : 0x40000000 [1 GiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
Reading Flash Content now ...
xGPT : Normalize settings Ok!
Brand : samsung
ProdName : SM-G9350
ProdModel : SM-G9350
Device : SM-G9350
AndroidVer: 6.0
MTKxCPU : MT6580
MTKxPRJ : alps-mp-m0.mp1-V2.34_hexing6580.we.m_P15
[Read Ok] : preloader_hexing6580_we_m.bin
[Read Ok] : lk.bin
[Read Ok] : boot.img
[Read Ok] : recovery.img
[Read Ok] : logo.bin
[Read Ok] : secro.img
[Read Ok] : system.img
[Read Ok] : cache.img
[Read Ok] : userdata.img
[ScatCFG] : MT6580 / V1.1.2 / hexing6580_we_m / EMMC
Android Info saved
MAUI Meta DB saved
HWConfig Info saved
FW Size : 1908 MiB
PRE-REQUISITE
- This is for Samsung S7 Edge Clone only.
- Your device must have 70% Of battery.
- You need a Laptop or PC to perform this Action.
- Download the right firmware for Samsung S7 Edge clone from the link bellow.
- Make sure you have followed the steps properly. Don’t Skip and Read!
- We are not responsible for any damage that you make to your Phone.
WHY YOU NEED TO FLASH YOUR PHONE!!
You need this firmware/stock rom if you have encountered this kind of problem in your Smartphone Listed Below:
1.Hang on logo.
2.Rebooting.
3.Bootloop & Dead boot after a wrong software.
4-Virus & Sexual Apps.
5-System crashing
2.Rebooting.
3.Bootloop & Dead boot after a wrong software.
4-Virus & Sexual Apps.
5-System crashing
How to know if the phone had a hard problem (Emmc problem)??
- What is Emmc problem? also called read mode only, it means that your internal memory doesnt accept command, so the phone stay on the same condition after a software or a hard reset.
- if the phone hang on logo after flash, you ara facing Emmc problem.
- As a precaution you shouldn't change setting in SP flashtool from Download only to format+download, you will end with a dead phone if you have a Emmc problem ofcourse.
DOWNLOAD AREA:
FIRMWARE DOWNLOAD LINK:
SP Flashtool Downloadlink: SPFlashTool 5.1628
Drivers Download Link: Mobile Mtk Drivers
REMARQUE:
MAKE BACKUP BEFORE FLASH
How To Flash Via SP FLASHTOOL?
1-Requirements:
- A Computer PC Run Windows XP or above
- Usb data cable (not a generic cable)
- Mtk usb drivers installed manually, you will find instruction bellow
- Your Mtk Smartphone Face a soft issue
- Original stock rom (you can find it above in download section)
- The latest SP Flashtool version
2-How to install VCOM Drivers:- Open device manager from my PC or my computer.
- Click on any item and go to actions > Add legacy hardware
- Now, press next and select install drivers manually
- Press next and click on have disk
- from the browse option, select VCOM drivers From mtk drivers folder
- Once its done. You will see a screen similar to this:
- Once you are done with the driver installation, go to device manager > Ports (COM&LPT) you will find a device similar to this:
3-How to flash rom using SP Flashtool?:- Power the phone off, remove the battery from the smartphone and put it back without booting the phone (if the battery is inside then simply switch it off).
- Launch SP Flashtool
*Double clicks onFlash_tool.exe
*Press OK
- Click on scatter-loading option and browse to the scatter file of your stock rom choose MTxxxx_android.txt (scatter.txt).
- Dont touch any options, Keep the original setting (In case you want to format device before flash press choose format+download but it'snt recommanded because you will be ended with an EMEI null)
- If you phone is alive and has a software issue (contain virus, Stuck on logo, apps setting problem, blink, or not work as expected) I advise you to Uncheck Preloader as a precaution. On contarary check all pertitions if you have a boot problem (you phone does'nt boot when you try to power on it).
- Once you are done with everything, click on the download button at the top of the software.
Stop should now be prominent while other options should be grayed out- Connect your switched off phone with battery inside to PC via Usb cable
- A progressbar should start running
- In the end of an success flash process, a box should show up with green OK symbol inside
- Disconnect the phone, remove the battery, slot it back in then power the phone.
ENJOY.
https://mega.nz/#!tIUXBJTb!UyyCLqr0rRmzxY35y-ZKIg7fBoPG05UwDMvh9wr5cHM
