GUIDE TO FLASH SAMSUNG GALAXY J3 SM-J300 CLONE MT6572 V1 CLONE FIRMWARE FREE
Exclusive is for free
INFO:
Waiting for USB Port...
Waiting for USB Port...
Abort by User
none usbport, maybe driver not installed
Definition Applied
Waiting for USB Port...
Set PreLoader USB VCOM Port (COM4)
Please Hold "ON" to connect with the phone...
Connected to Phone.
CPU: MT6572 SW:0000 Ver: CA01
Downloading Boot8 ...
EMMC Size: 0x00E9000000
Flash Type: EMMC
INT/EXT RAM Size: 0x0+0x0
Reading infr(EMMC)...
PRELOADER BaseAddr:0x0 Size:0xC00000
MBR BaseAddr:0xC00000 Size:0x80000
EBR1 BaseAddr:0xC80000 Size:0x80000
PRO_INFO BaseAddr:0xD00000 Size:0x300000
NVRAM BaseAddr:0x1000000 Size:0x500000
PROTECT_F BaseAddr:0x1500000 Size:0xA00000
PROTECT_S BaseAddr:0x1F00000 Size:0xA00000
SECCFG BaseAddr:0x2900000 Size:0x20000
UBOOT BaseAddr:0x2920000 Size:0x60000
BOOTIMG BaseAddr:0x2980000 Size:0x600000
RECOVERY BaseAddr:0x2F80000 Size:0x600000
SEC_RO BaseAddr:0x3580000 Size:0x40000
MISC BaseAddr:0x35C0000 Size:0x80000
LOGO BaseAddr:0x3640000 Size:0x300000
EXPDB BaseAddr:0x3940000 Size:0xA00000
ANDROID BaseAddr:0x4340000 Size:0x2BC00000
CACHE BaseAddr:0x2FF40000 Size:0xE200000
USRDATA BaseAddr:0x3E140000 Size:0x52C00000
FAT BaseAddr:0x90D40000 Size:0x56FE0000
BMTPOOL BaseAddr:0xFFFF00A8 Size:0x1500000
BaseAddr:0x0 Size:0x0
>>Done.
PRE-REQUISITE
- This is for J3109 Clone only.
- Your device must have 70% Of battery.
- You need a Laptop or PC to perform this Action.
- Download the right firmware for J3109 clone from the link bellow.
- Make sure you have followed the steps properly. Don’t Skip and Read!
- We are not responsible for any damage that you make to your Phone.
WHY YOU NEED TO FLASH YOUR PHONE!!
You need this firmware/stock rom if you have encountered this kind of problem in your Smartphone Listed Below:
1.Hang on logo.
2.Rebooting.
3.Bootloop & Dead boot after a wrong software.
4-Virus & Sexual Apps.
5-System crashing
2.Rebooting.
3.Bootloop & Dead boot after a wrong software.
4-Virus & Sexual Apps.
5-System crashing
How to know if the phone had a hard problem (Emmc problem)??
- What is Emmc problem? also called read mode only, it means that your internal memory doesnt accept command, so the phone stay on the same condition after a software or a hard reset.
- if the phone hang on logo after flash, you ara facing Emmc problem.
- As a precaution you shouldn't change setting in SP flashtool from Download only to format+download, you will end with a dead phone if you have a Emmc problem ofcourse.
DOWNLOAD AREA:
FIRMWARE DOWNLOAD LINK:
SP Flashtool Downloadlink: SPFlashTool 5.1628
Drivers Download Link: Mobile Mtk Drivers
REMARQUE:
MAKE BACKUP BEFORE FLASH
How To Flash Via SP FLASHTOOL?
1-Requirements:
- A Computer PC Run Windows XP or above
- Usb data cable (not a generic cable)
- Mtk usb drivers installed manually, you will find instruction bellow
- Your Mtk Smartphone Face a soft issue
- Original stock rom (you can find it above in download section)
- The latest SP Flashtool version
2-How to install VCOM Drivers:- Open device manager from my PC or my computer.
- Click on any item and go to actions > Add legacy hardware
- Now, press next and select install drivers manually
- Press next and click on have disk
- from the browse option, select VCOM drivers From mtk drivers folder
- Once its done. You will see a screen similar to this:
- Once you are done with the driver installation, go to device manager > Ports (COM&LPT) you will find a device similar to this:
3-How to flash rom using SP Flashtool?:- Power the phone off, remove the battery from the smartphone and put it back without booting the phone (if the battery is inside then simply switch it off).
- Launch SP Flashtool
*Double clicks onFlash_tool.exe*Press OK- Click on scatter-loading option and browse to the scatter file of your stock rom choose MTxxxx_android.txt (scatter.txt).
- Dont touch any options, Keep the original setting (In case you want to format device before flash press choose format+download but it'snt recommanded because you will be ended with an EMEI null)
- If you phone is alive and has a software issue (contain virus, Stuck on logo, apps setting problem, blink, or not work as expected) I advise you to Uncheck Preloader as a precaution. On contarary check all pertitions if you have a boot problem (you phone does'nt boot when you try to power on it).
- Once you are done with everything, click on the download button at the top of the software.
Stop should now be prominent while other options should be grayed out- Connect your switched off phone with battery inside to PC via Usb cable
- A progressbar should start running
- In the end of an success flash process, a box should show up with green OK symbol inside
- Disconnect the phone, remove the battery, slot it back in then power the phone.
ENJOY.
https://mega.nz/#!tIUXBJTb!UyyCLqr0rRmzxY35y-ZKIg7fBoPG05UwDMvh9wr5cHM
https://mega.nz/#!tIUXBJTb!UyyCLqr0rRmzxY35y-ZKIg7fBoPG05UwDMvh9wr5cHM