Guide To Flash Oppo JOY3 A11W MT6582 Android 4.4.2 By mtk fashtool tested firmware

OPPO JOY3 A11W MT6580 ANDROID 4.4.2
 TESTED FIRMWARE FREE DOWNLOAD

INFO

• Brand : OPPO
• ProdName : A11w
• ProdModel : A11w
• Device : A11w
• AndroidVer: 4.4.2
• MTKxCPU : MT6582
• MTKxPRJ : A11wEX_11_A.07_151214
• CPU: MT6582 SW:0001 Ver: CA01
• Downloading Boot8 ...
• EMMC Size: 0x03A3E00000
• Flash Type: EMMC
• INT/EXT RAM Size: 0x0+0x0
• Reading infr(EMMC)...
• model:A11w
• brand:OPPO
• id:A11wEX_11_151214
• version:4.4.2
• model:A11w
• brand:OPPO
• manufacturer:OPPO
• PRELOADER BaseAddr:0x0 Size:0x1400000
• MBR BaseAddr:0x1400000 Size:0x80000
• EBR1 BaseAddr:0x1480000 Size:0x80000
• PRO_INFO BaseAddr:0x1500000 Size:0x300000
• NVRAM BaseAddr:0x1800000 Size:0x500000
• PROTECT_F BaseAddr:0x1D00000 Size:0xA00000
• PROTECT_S BaseAddr:0x2700000 Size:0xA00000
• SECCFG BaseAddr:0x3100000 Size:0x20000
• UBOOT BaseAddr:0x3120000 Size:0x60000
• BOOTIMG BaseAddr:0x3180000 Size:0x1000000
• RECOVERY BaseAddr:0x4180000 Size:0x1000000
• SEC_RO BaseAddr:0x5180000 Size:0x600000
• MISC BaseAddr:0x5780000 Size:0x80000
• LOGO BaseAddr:0x5800000 Size:0x300000
• EBR2 BaseAddr:0x5B00000 Size:0x80000
• OPPO_CUSTOM BaseAddr:0x5B80000 Size:0x100000
• RESERVE1 BaseAddr:0x5C80000 Size:0x1000000
• RESERVE2 BaseAddr:0x6C80000 Size:0x2000000
• EXPDB BaseAddr:0x8C80000 Size:0xA00000
• ANDROID BaseAddr:0x9680000 Size:0x60000000
• CACHE BaseAddr:0x69680000 Size:0x7E00000
• USRDATA BaseAddr:0x71480000 Size:0x332080000
• BMTPOOL BaseAddr:0xFFFF0000 Size:0x1500000

PRE-REQUISITE

• This is for Oppo A11w only.
• Your device must have 70% Of battery.
• You need a Laptop or PC to perform this Action.
• Download the right firmware for Oppo A11w from the link bellow.
• Make sure you have followed the steps properly. Don’t Skip and Read!
• We are not responsible for any damage that you make to your Phone.
  

WHY YOU NEED TO FLASH YOUR PHONE!!
You need this firmware/stock rom if you have encountered this kind of problem in your Smartphone Listed Below:

1.Hang on logo.

2.Rebooting.
3.Bootloop & Dead boot after a wrong software.
4-Virus & Sexual Apps.
5-System crashing

How to know if the phone had a hard problem (Emmc problem)??

• What is Emmc problem? also called read mode only,  it means that your internal memory doesnt accept command, so the phone stay on the same condition after a software or a hard reset.
•  if the phone hang on logo after flash, you ara facing Emmc problem.
• As a precaution you shouldn't change setting in SP flashtool from Download only to format+download, you will end with a dead phone if you have a Emmc problem ofcourse.

REMARQUE:

MAKE BACKUP BEFORE FLASH

DOWNLOAD AREA:

FIRMWARE DOWNLOAD LINK: OPPO JOY3 A11W MT6582

SP Flashtool Downloadlink: SPFlashTool 5.1628

Drivers Download Link: Mobile Mtk Drivers 

How To Flash Via SP FLASHTOOL?

1. • A Computer PC Run Windows XP or above
   • Usb data cable (not a generic cable)
   • Mtk usb drivers installed manually, you will find instruction bellow
   • Your Mtk Smartphone Face a soft issue
   • Original stock rom (you can find it above in download section)
   • The latest SP Flashtool version
   
   
   2-How to install VCOM Drivers:
   • Open device manager from my PC or my computer.
   • Click on any item and go to actions > Add legacy hardware
   • Now, press next and select install drivers manually
   • Press next and click on have disk
   • from the browse option, select VCOM drivers From mtk drivers folder
   • Once its done. You will see a screen similar to this:
   
   
   
   
   
   
   
   
   
   • Once you are done with the driver installation, go to device manager > Ports (COM&LPT) you will find a device similar to this:
   
   
   
   
   
   
   
   3-How to flash rom using SP Flashtool?:
   
   
   • Power the phone off, remove the battery from the smartphone and put it back without booting the phone (if the battery is inside then simply switch it off).
   • Launch SP Flashtool 
   
   
   
   *Double clicks onFlash_tool.exe
   
                                          *Press OK
   
   
   
   
   
   
   
   
   
   
   
   
   
   • Click on scatter-loading option and browse to the scatter file of your stock rom choose MTxxxx_android.txt (scatter.txt).
   
   
   
   
   
   
   
   
   
   
   • Dont touch any options, Keep the original setting (In case you want to format device before flash press choose format+download but it'snt recommanded because you will be ended with an EMEI null)
   • If you phone is alive and has a software issue (contain virus, Stuck on logo, apps setting problem, blink, or not work as expected) I advise you to Uncheck Preloader as a precaution. On contarary check all pertitions if you have a boot problem (you phone does'nt boot when you try to power on it).
                                  
   
   
   
   • Once you are done with everything, click on the download button at the top of the software.
   
   
   
   
   
   
   
   Stop should now be prominent while other options should be grayed out
   
   
   
   
   • Connect your switched off phone with battery inside to PC via Usb cable
   • A progressbar should start running
   
   
   
   
   
   • In the end of an success flash process, a box should show up with green OK symbol inside
   
   
   
   
   
   • Disconnect the phone, remove the battery, slot it back in then power the phone.

ENJOY.