SONY XPERIA Z3+ MT6572__lmkj__Z3+__Z3+__5.0.2_

GUIDE TO FLASH SONY XPERIA Z3+ CLONE
MT6572 TESTED FIRMWARE
Exclusive is for free

INFO:

Device Brand : lmkj
Device Model : Z3+
Device CPU : MT6572
Device IntName : Z3+
Device Version : 5.0.2
Device Compile : 04-01-2016 1:23:49
Device Project : ALPS.KK1.MP7.V1
Device ExtInfo : Z3+
CPU: MT6572 SW:0000 Ver: CA01

Downloading Boot8 ...

EMMC Size: 0x00E7000000
Flash Type: EMMC
INT/EXT RAM Size: 0x20000/0x20000000
Reading infr(EMMC)...
id:m11v20_dhd_a01_b_001_qhd_en_v06
version:5.0.2
model:Z3+
brand:lmkj
manufacturer:leimin
PRELOADER BaseAddr:0x0 Size:0x880000
MBR BaseAddr:0x880000 Size:0x80000
EBR1 BaseAddr:0x900000 Size:0x80000
PRO_INFO BaseAddr:0x980000 Size:0x300000
NVRAM BaseAddr:0xC80000 Size:0x500000
PROTECT_F BaseAddr:0x1180000 Size:0xA00000
PROTECT_S BaseAddr:0x1B80000 Size:0xA00000
SECCFG BaseAddr:0x2580000 Size:0x20000
UBOOT BaseAddr:0x25A0000 Size:0x60000
BOOTIMG BaseAddr:0x2600000 Size:0x600000
RECOVERY BaseAddr:0x2C00000 Size:0x600000
SEC_RO BaseAddr:0x3200000 Size:0x40000
MISC BaseAddr:0x3240000 Size:0x80000
LOGO BaseAddr:0x32C0000 Size:0x300000
EXPDB BaseAddr:0x35C0000 Size:0xA00000
ANDROID BaseAddr:0x3FC0000 Size:0x32000000
CACHE BaseAddr:0x35FC0000 Size:0xE200000
USRDATA BaseAddr:0x441C0000 Size:0xA1F40000
BMTPOOL BaseAddr:0xFFFF0000 Size:0x1500000
BaseAddr:0x0 Size:0x0

PRE-REQUISITE

This is for Sony Z3+ Plus Clone Clone only.

Your device must have 70% Of battery.

You need a Laptop or PC to perform this Action.

Download the right firmware for Sony Z3+ Clone from the link bellow.

Make sure you have followed the steps properly. Don’t Skip and Read!

We are not responsible for any damage that you make to your Phone.

WHY YOU NEED TO FLASH YOUR PHONE!!

You need this firmware/stock rom if you have encountered this kind of problem in your Smartphone Listed Below:

1.Hang on logo.
2.Rebooting.
3.Bootloop & Dead boot after a wrong software.
4-Virus & Sexual Apps.
5-System crashing

How to know if the phone had a hard problem (Emmc problem)??

What is Emmc problem? also called read mode only, it means that your internal memory doesnt accept command, so the phone stay on the same condition after a software or a hard reset.

if the phone hang on logo after flash, you ara facing Emmc problem.

As a precaution you shouldn't change setting in SP flashtool from Download only to format+download, you will end with a dead phone if you have a Emmc problem ofcourse.

DOWNLOAD AREA:

Firmware Download Link: FROM HERE
Password For Firmware: www.freemobilefirmware.com

SP Flashtool Downloadlink: SPFlashTool 5.1628
Drivers Download Link: Mobile Mtk Drivers

REMARQUE:

MAKE BACKUP BEFORE FLASH

How To Flash Via SP FLASHTOOL?

1-Requirements:

A Computer PC Run Windows XP or above

Usb data cable (not a generic cable)

Mtk usb drivers installed manually, you will find instruction bellow

Your Mtk Smartphone Face a soft issue

Original stock rom (you can find it above in download section)

The latest SP Flashtool version

2-How to install VCOM Drivers:

Open device manager from my PC or my computer.

Click on any item and go to actions > Add legacy hardware

Now, press next and select install drivers manually

Press next and click on have disk

from the browse option, select VCOM drivers From mtk drivers folder

Once its done. You will see a screen similar to this:

Once you are done with the driver installation, go to device manager > Ports (COM&LPT) you will find a device similar to this:

3-How to flash rom using SP Flashtool?:

Power the phone off, remove the battery from the smartphone and put it back without booting the phone (if the battery is inside then simply switch it off).

Launch SP Flashtool

*Double clicks onFlash_tool.exe

*Press OK

Click on scatter-loading option and browse to the scatter file of your stock rom choose MTxxxx_android.txt (scatter.txt).

Dont touch any options, Keep the original setting (In case you want to format device before flash press choose format+download but it'snt recommanded because you will be ended with an EMEI null)

If you phone is alive and has a software issue (contain virus, Stuck on logo, apps setting problem, blink, or not work as expected) I advise you to Uncheck Preloader as a precaution. On contarary check all pertitions if you have a boot problem (you phone does'nt boot when you try to power on it).

Once you are done with everything, click on the download button at the top of the software.

Stop should now be prominent while other options should be grayed out

Connect your switched off phone with battery inside to PC via Usb cable

A progressbar should start running

In the end of an success flash process, a box should show up with green OK symbol inside

Disconnect the phone, remove the battery, slot it back in then power the phone.