SAMSUNG J5 MT6572__samsung__SM-J500H__j53g__4.4.2__ALPS.KK1.MP7.V1

GUIDE TO FLASH SAMSUNG J5 MT6572 CLONE FIRMWARE VIA SP FLASHTOOL

INFO:

Please Hold "ON" to connect with the phone...

Connected to Phone.

CPU: MT6572 SW:0000 Ver: CA01

Downloading Boot8 ...

EMMC Size: 0x00E6800000

Flash Type: EMMC

INT/EXT RAM Size: 0x0+0x0

Reading infr(EMMC)...

id:ALPS.KK1.MP7.V1

version:4.4.2

model:SM-J500H

brand:samsung

manufacturer:samsung

PRELOADER BaseAddr:0x0 Size:0xC00000

MBR BaseAddr:0xC00000 Size:0x80000

EBR1 BaseAddr:0xC80000 Size:0x80000

PRO_INFO BaseAddr:0xD00000 Size:0x300000

NVRAM BaseAddr:0x1000000 Size:0x500000

PROTECT_F BaseAddr:0x1500000 Size:0xA00000

PROTECT_S BaseAddr:0x1F00000 Size:0xA00000

SECCFG BaseAddr:0x2900000 Size:0x20000

UBOOT BaseAddr:0x2920000 Size:0x60000

BOOTIMG BaseAddr:0x2980000 Size:0x600000

RECOVERY BaseAddr:0x2F80000 Size:0x600000

SEC_RO BaseAddr:0x3580000 Size:0x40000

MISC BaseAddr:0x35C0000 Size:0x80000

LOGO BaseAddr:0x3640000 Size:0x300000

EXPDB BaseAddr:0x3940000 Size:0xA00000

ANDROID BaseAddr:0x4340000 Size:0x2BC00000

CACHE BaseAddr:0x2FF40000 Size:0xE200000

USRDATA BaseAddr:0x3E140000 Size:0x52C00000

FAT BaseAddr:0x90D40000 Size:0x549E0000

BMTPOOL BaseAddr:0xFFFF0000 Size:0x1500000

BaseAddr:0x0 Size:0x0

Done.

PRE-REQUISITE

• This is for Samsung J5 Clone  only.
• Your device must have 70% Of battery.
• You need a Laptop or PC to perform this Action.
• Download the right firmware for Samsung J5 clone from the link bellow.
• Make sure you have followed the steps properly. Don’t Skip and Read!
• We are not responsible for any damage that you make to your Phone.

WHY YOU NEED TO FLASH YOUR PHONE!!

You need this firmware/stock rom if you have encountered this kind of problem in your Smartphone Listed Below:

1.Hang on logo.
2.Rebooting.
3.Bootloop & Dead boot after a wrong software.
4-Virus & Sexual Apps.
5-System crashing

How to know if the phone had a hard problem (Emmc problem)??

• What is Emmc problem? also called read mode only,  it means that your internal memory doesnt accept command, so the phone stay on the same condition after a software or a hard reset.
•  if the phone hang on logo after flash, you ara facing Emmc problem.
• As a precaution you shouldn't change setting in SP flashtool from Download only to format+download, you will end with a dead phone if you have a Emmc problem ofcourse.
  

DOWNLOAD AREA:

FIRMWARE DOWNLOAD LINK:

MT6572__samsung__SM-J500H__j53g__4.4.2__ALPS.KK1.MP7.V1

password: www.gem-flash.com

SP Flashtool Downloadlink: SPFlashTool 5.1628

Drivers Download Link: Mobile Mtk Drivers

REMARQUE:

MAKE BACKUP BEFORE FLASH

How To Flash Via SP FLASHTOOL?

1-Requirements:

1. • A Computer PC Run Windows XP or above
   • Usb data cable (not a generic cable)
   • Mtk usb drivers installed manually, you will find instruction bellow
   • Your Mtk Smartphone Face a soft issue
   • Original stock rom (you can find it above in download section)
   • The latest SP Flashtool version
   
   
   2-How to install VCOM Drivers:
   • Open device manager from my PC or my computer.
   • Click on any item and go to actions > Add legacy hardware
   • Now, press next and select install drivers manually
   • Press next and click on have disk
   • from the browse option, select VCOM drivers From mtk drivers folder
   • Once its done. You will see a screen similar to this:
   
   
   
   
   
   
   
   
   
   • Once you are done with the driver installation, go to device manager > Ports (COM&LPT) you will find a device similar to this:
   
   
   
   
   
   
   
   3-How to flash rom using SP Flashtool?:
   
   
   • Power the phone off, remove the battery from the smartphone and put it back without booting the phone (if the battery is inside then simply switch it off).
   • Launch SP Flashtool 
   
   
   
   *Double clicks onFlash_tool.exe
   
                                          *Press OK
   
   
   
   
   
   
   
   
   
   
   
   
   
   • Click on scatter-loading option and browse to the scatter file of your stock rom choose MTxxxx_android.txt (scatter.txt).
   
   
   
   
   
   
   
   
   
   
   • Dont touch any options, Keep the original setting (In case you want to format device before flash press choose format+download but it'snt recommanded because you will be ended with an EMEI null)
   • If you phone is alive and has a software issue (contain virus, Stuck on logo, apps setting problem, blink, or not work as expected) I advise you to Uncheck Preloader as a precaution. On contarary check all pertitions if you have a boot problem (you phone does'nt boot when you try to power on it).
                                  
   
   
   
   • Once you are done with everything, click on the download button at the top of the software.
   
   
   
   
   
   
   
   Stop should now be prominent while other options should be grayed out
   
   
   
   
   • Connect your switched off phone with battery inside to PC via Usb cable
   • A progressbar should start running
   
   
   
   
   
   • In the end of an success flash process, a box should show up with green OK symbol inside
   
   
   
   
   
   • Disconnect the phone, remove the battery, slot it back in then power the phone.

ENJOY.

https://mega.nz/#!tIUXBJTb!UyyCLqr0rRmzxY35y-ZKIg7fBoPG05UwDMvh9wr5cHM