GUIDE TO FLASH ALCATEL POP 5 OT-5037E MT6572 TESTED FIRMWARE FREE DOWNLOAD
INFO:
- BB_CPU_ID : 6572
- BB_CPU_HW : CA01
- BB_CPU_SW : 8A00
- BB_CPU_SB : 0000
- BB_CPU_NM : [MediaTek] MT6572_S00
- Processing BROM stage
- BLVersion : 0x01
- SecCfgVal : 0x00000000
- BromVersion : 0xFF
- BLVersion : 0x01
- Preloader Status : Alive
- Processing DA stage
- DA Select done , sending
- DA Ver : MTK_AllInOne_DA_v7.1533.03
- NAND_ID : 00000000000000000000000000000000
- eMMC_ID : 1501004E35575A4D42018197DC9F41C7
- DA Stat : v4.2 on BBID : 0x88
- DA Sent. Configure setting now ...
- DA started successuflly
- eMMC FlashIC initialized
- [eMMC] : FLASH_VEN : 0015 , OEM : 0100
- [eMMC] : FLASH_INF : BMZW5
- [eMMC] : FLASH_CID : 1501004E35575A4D42018197DC9F41C7
- [eMMC] : FLASH_EXT : 00200000/00080000
- [eMMC] : FLASH_LEN : 0x00000000E9000000
- INT RAM : 0x00020000
- EXT RAM : 0x20000000
- BOOT TYPE : EMMC_FLASH_BOOT
- SOC VERIFY : C1
- Brand: TCT
- ProdName: ALCATEL_ONE_TOUCH_5037E
- ProdModel: ALCATEL ONE TOUCH 5037E
- Device: YarisL_GSM
- AndroidVer: 4.2.2
- MTKxCPU: MT6572
- MTKxPRJ: ALPS.JB3.MP.V1
PRE-REQUISITE
- This is for Alcatel Pop 5 Clone only.
- Your device must have 70% Of battery.
- You need a Laptop or PC to perform this Action.
- Download the right firmware for Alcatel Pop 5 from the link bellow.
- Make sure you have followed the steps properly. Don’t Skip and Read!
- We are not responsible for any damage that you make to your Phone.
You need this firmware/stock rom if you have encountered this kind of problem in your Smartphone Listed Below:
- 1.Hang on logo.
- 2.Rebooting.
- 3.Bootloop & Dead boot after a wrong software.
- 4-Virus & Sexual Apps.
- 5-System crashing
How to know if the phone had a hard problem (Emmc problem)??
- What is Emmc problem? also called read mode only, it means that your internal memory doesnt accept command, so the phone stay on the same condition after a software or a hard reset.
- if the phone hang on logo after flash, you ara facing Emmc problem.
- As a precaution you shouldn't change setting in SP flashtool from Download only to format+download, you will end with a dead phone if you have a Emmc problem ofcourse.
DOWNLOAD AREA:
Firmware Download Link: MT6572__TCT__ALCATEL ONE TOUCH 5037E__YarisL_GSM__4.2.2__ALPS.JB3.MP.V1
Password For Firmware: www.freemobilefirmware.com
SP Flashtool Downloadlink: SPFlashTool 5.1628
Drivers Download Link: Mobile Mtk Drivers
REMARQUE:
MAKE BACKUP BEFORE FLASH
How To Flash Via SP FLASHTOOL?
1-Requirements:
- A Computer PC Run Windows XP or above
- Usb data cable (not a generic cable)
- Mtk usb drivers installed manually, you will find instruction bellow
- Your Mtk Smartphone Face a soft issue
- Original stock rom (you can find it above in download section)
- The latest SP Flashtool version
2-How to install VCOM Drivers:- Open device manager from my PC or my computer.
- Click on any item and go to actions > Add legacy hardware
- Now, press next and select install drivers manually
- Press next and click on have disk
- from the browse option, select VCOM drivers From mtk drivers folder
- Once its done. You will see a screen similar to this:
- Once you are done with the driver installation, go to device manager > Ports (COM&LPT) you will find a device similar to this:
3-How to flash rom using SP Flashtool?:- Power the phone off, remove the battery from the smartphone and put it back without booting the phone (if the battery is inside then simply switch it off).
- Launch SP Flashtool
*Double clicks onFlash_tool.exe
*Press OK
- Click on scatter-loading option and browse to the scatter file of your stock rom choose MTxxxx_android.txt (scatter.txt).
- Dont touch any options, Keep the original setting (In case you want to format device before flash press choose format+download but it'snt recommanded because you will be ended with an EMEI null)
- If you phone is alive and has a software issue (contain virus, Stuck on logo, apps setting problem, blink, or not work as expected) I advise you to Uncheck Preloader as a precaution. On contarary check all pertitions if you have a boot problem (you phone does'nt boot when you try to power on it).
- Once you are done with everything, click on the download button at the top of the software.
Stop should now be prominent while other options should be grayed out- Connect your switched off phone with battery inside to PC via Usb cable
- A progressbar should start running
- In the end of an success flash process, a box should show up with green OK symbol inside
- Disconnect the phone, remove the battery, slot it back in then power the phone.
ENJOY.
