MT6589__samsung__SM-J700H__j73g__5.1.1__ALPS.JB2.MP.V1.16

GUIDE TO FLASH SAMSUNG GALAXY J7 CLONE FIRMWARE TESTED FILE VIA MTK FLASHTOOL

INFO:

Inital Boot Ok!

BB_CPU_PID : 6583

BB_CPU_NME : [MediaTek] MT6583|6589_S00

BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000

Processing BROM stage

Settings for BROM configured!

SecCfgVal : 0x00000000

BromVer : 0x00FF

BLVersion : 0x0001

PreLoader : Active [ Boot with PL ]

BootLdrSS : NORMAL with PRELOADER

Processing DA stage

DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07

Sending and initialize DA ...

Running DA ver.3.2 on BBID : 0x86

NAND Flash : NOT INSTALLED

eMMC Flash : 484A019064314734A2018604A961BC1B

Initialize Memory ... 

DRAM already initialized by Preloader

DAgent sent , init HW now

eMMC FlashIC initialized

[eMMC] : FLASH_VEN : 0x90 , OEM : 014A

[eMMC] : FLASH_INF : [HYNIX] , d1G4

[eMMC] : FLASH_CID : 90014A4834473164048601A21BBC61A9

[eMMC] : FLASH_BRT : 0x00200000 , 0x00200000 , 0x00200000

[eMMC] : FLASH_LEN : 0x00000000E7000000

[eMMC] : FLASH_UCP : 3696 MiB [eMMC 4 GiB]

DEV RID : 0x0D22E2284EBC5F7BBDA9D7FD7E2AF42F

INT RAM : 0x00020000

EXT RAM : 0x20000000 [512 MiB]

BOOT TYPE : EMMC_FLASH_BOOT

SOC VERIFY : C1

Boot Ok!

Brand : samsung

ProdName : j73gxx

ProdModel : SM-J700H

Device : j73g

AndroidVer: 5.1.1

MTKxCPU : MT6589

MTKxPRJ : ALPS.JB2.MP.V1.16

[Read Ok] : preloader_mbk89_wet_jb2.bin

[Read Ok] : MBR

[Read Ok] : EBR1

[Read Ok] : lk.bin

[Read Ok] : boot.img

[Read Ok] : recovery.img

[Read Ok] : secro.img

[Read Ok] : logo.bin

[Read Ok] : system.img

[Read Ok] : cache.img

[Read Ok] : userdata.img

[ScatCFG] : MT6589 / V1.0.0 / mbk89_wet_jb2 / EMMC

Android Info saved

MAUI Meta DB saved

HWConfig Info saved

FW Size : 790 MiB

Scatter saved to : 

MT6589__samsung__SM-J700H__j73g__5.1.1__ALPS.JB2.MP.V1.16

preloader_mbk89_wet_jb2 (126Kb)

PRE-REQUISITE

• This is for J7 Clone  only.
• Your device must have 70% Of battery.
• You need a Laptop or PC to perform this Action.
• Download the right firmware for j7 clone from the link bellow.
• Make sure you have followed the steps properly. Don’t Skip and Read!
• We are not responsible for any damage that you make to your Phone.
  

WHY YOU NEED TO FLASH YOUR PHONE!!

You need this firmware/stock rom if you have encountered this kind of problem in your Smartphone Listed Below:

1.Hang on logo.
2.Rebooting.
3.Bootloop & Dead boot after a wrong software.
4-Virus & Sexual Apps.
5-System crashing

How to know if the phone had a hard problem (Emmc problem)??

• What is Emmc problem? also called read mode only,  it means that your internal memory doesnt accept command, so the phone stay on the same condition after a software or a hard reset.
•  if the phone hang on logo after flash, you ara facing Emmc problem.
• As a precaution you shouldn't change setting in SP flashtool from Download only to format+download, you will end with a dead phone if you have a Emmc problem ofcourse.

DOWNLOAD AREA:

FIRMWARE DOWNLOAD LINK:

MT6589__samsung__SM-J700H__j73g__5.1.1__ALPS.JB2.MP.V1.16

SP Flashtool Downloadlink: SPFlashTool 5.1628

Drivers Download Link: Mobile Mtk Drivers

REMARQUE:

MAKE BACKUP BEFORE FLASH

How To Flash Via SP FLASHTOOL?

1-Requirements:

1. • A Computer PC Run Windows XP or above
   • Usb data cable (not a generic cable)
   • Mtk usb drivers installed manually, you will find instruction bellow
   • Your Mtk Smartphone Face a soft issue
   • Original stock rom (you can find it above in download section)
   • The latest SP Flashtool version
   
   
   2-How to install VCOM Drivers:
   • Open device manager from my PC or my computer.
   • Click on any item and go to actions > Add legacy hardware
   • Now, press next and select install drivers manually
   • Press next and click on have disk
   • from the browse option, select VCOM drivers From mtk drivers folder
   • Once its done. You will see a screen similar to this:
   
   
   
   
   
   
   
   
   
   • Once you are done with the driver installation, go to device manager > Ports (COM&LPT) you will find a device similar to this:
   
   
   
   
   
   
   
   3-How to flash rom using SP Flashtool?:
   
   
   • Power the phone off, remove the battery from the smartphone and put it back without booting the phone (if the battery is inside then simply switch it off).
   • Launch SP Flashtool 
   
   
   
   *Double clicks onFlash_tool.exe
   
                                          *Press OK
   
   
   
   
   
   
   
   
   
   
   
   
   
   • Click on scatter-loading option and browse to the scatter file of your stock rom choose MTxxxx_android.txt (scatter.txt).
   
   
   
   
   
   
   
   
   
   
   • Dont touch any options, Keep the original setting (In case you want to format device before flash press choose format+download but it'snt recommanded because you will be ended with an EMEI null)
   • If you phone is alive and has a software issue (contain virus, Stuck on logo, apps setting problem, blink, or not work as expected) I advise you to Uncheck Preloader as a precaution. On contarary check all pertitions if you have a boot problem (you phone does'nt boot when you try to power on it).
                                  
   
   
   
   • Once you are done with everything, click on the download button at the top of the software.
   
   
   
   
   
   
   
   Stop should now be prominent while other options should be grayed out
   
   
   
   
   • Connect your switched off phone with battery inside to PC via Usb cable
   • A progressbar should start running
   
   
   
   
   
   • In the end of an success flash process, a box should show up with green OK symbol inside
   
   
   
   
   
   • Disconnect the phone, remove the battery, slot it back in then power the phone.

ENJOY.