MT6582__Samsung__SM-J3109__Galaxy_J3__4.2.2__J8251_SM_DZ_4.2_V1.2

GUIDE TO FlASH SAMSUNG GALAXY J3 SM-J3109 MT6582 CLONE FIRMWARE VIA FLASHTOOL

INFO:

CPU: MT6582 SW:0001 Ver: CA01  Downloading Boot8 ...

  EMMC Size: 0x00E9000000

  Flash Type: EMMC

 Created by Infinity-Box (c) Chinese Miracle II (c) 2016Device Brand   : Samsung

Device Model   : Galaxy J3

Device CPU     : MT6582

Device IntName : SM-J3109

Device Version : 4.2.2

Device Compile : 10-05-2016 2:14:56

Device Project : J8251_SM_DZ_4.2_V1.2

Device ExtInfo : SM-J3109 

INT/EXT RAM  Size: 0x20000/0x20000000

  Reading infr(EMMC)...

  id:J8251_SM_DZ_4.2_V1.2

  version:4.2.2

  model:SM-J3109

  brand:Samsung

  manufacturer:Samsung

  PRELOADER  BaseAddr:0x0  Size:0x1400000

  MBR  BaseAddr:0x1400000  Size:0x80000

  EBR1  BaseAddr:0x1480000  Size:0x80000

  PRO_INFO  BaseAddr:0x1500000  Size:0x300000

  NVRAM  BaseAddr:0x1800000  Size:0x500000

  PROTECT_F  BaseAddr:0x1D00000  Size:0xA00000

  PROTECT_S  BaseAddr:0x2700000  Size:0xA00000

  SECCFG  BaseAddr:0x3100000  Size:0x20000

  UBOOT  BaseAddr:0x3120000  Size:0x60000

  BOOTIMG  BaseAddr:0x3180000  Size:0x600000

  RECOVERY  BaseAddr:0x3780000  Size:0x600000

  SEC_RO  BaseAddr:0x3D80000  Size:0x600000

  MISC  BaseAddr:0x4380000  Size:0x80000

  LOGO  BaseAddr:0x4400000  Size:0x300000

  EXPDB  BaseAddr:0x4700000  Size:0xA00000

  ANDROID  BaseAddr:0x5100000  Size:0x4BC00000

  CACHE  BaseAddr:0x50D00000  Size:0x7E00000

  USRDATA  BaseAddr:0x58B00000  Size:0x8F220000

  BMTPOOL  BaseAddr:0xFFFF0000  Size:0x0

>>Done.

PRE-REQUISITE

• This is for J3 Clone  only.
• Your device must have 70% Of battery.
• You need a Laptop or PC to perform this Action.
• Download the right firmware for j3 clone from the link bellow.
• Make sure you have followed the steps properly. Don’t Skip and Read!
• We are not responsible for any damage that you make to your Phone.
  

WHY YOU NEED TO FLASH YOUR PHONE!!

You need this firmware/stock rom if you have encountered this kind of problem in your Smartphone Listed Below:

1.Hang on logo.
2.Rebooting.
3.Bootloop & Dead boot after a wrong software.
4-Virus & Sexual Apps.
5-System crashing


How to know if the phone had a hard problem (Emmc problem)??

• What is Emmc problem? also called read mode only,  it means that your internal memory doesnt accept command, so the phone stay on the same condition after a software or a hard reset.
•  if the phone hang on logo after flash, you ara facing Emmc problem.
• As a precaution you shouldn't change setting in SP flashtool from Download only to format+download, you will end with a dead phone if you have a Emmc problem ofcourse.

DOWNLOAD AREA:

FIRMWARE DOWNLOAD LINK:

MT6582__Samsung__SM-J3109__Galaxy_J3__4.2.2__J8251_SM_DZ_4.2_V1.2

SP Flashtool Downloadlink: SPFlashTool 5.1628

Drivers Download Link: Mobile Mtk Drivers

REMARQUE:

MAKE BACKUP BEFORE FLASH

How To Flash Via SP FLASHTOOL?

1-Requirements:

1. • A Computer PC Run Windows XP or above
   • Usb data cable (not a generic cable)
   • Mtk usb drivers installed manually, you will find instruction bellow
   • Your Mtk Smartphone Face a soft issue
   • Original stock rom (you can find it above in download section)
   • The latest SP Flashtool version
   
   
   2-How to install VCOM Drivers:
   • Open device manager from my PC or my computer.
   • Click on any item and go to actions > Add legacy hardware
   • Now, press next and select install drivers manually
   • Press next and click on have disk
   • from the browse option, select VCOM drivers From mtk drivers folder
   • Once its done. You will see a screen similar to this:
   
   
   
   
   
   
   
   
   
   • Once you are done with the driver installation, go to device manager > Ports (COM&LPT) you will find a device similar to this:
   
   
   
   
   
   
   
   3-How to flash rom using SP Flashtool?:
   
   
   • Power the phone off, remove the battery from the smartphone and put it back without booting the phone (if the battery is inside then simply switch it off).
   • Launch SP Flashtool 
   
   
   
   *Double clicks onFlash_tool.exe
   
                                          *Press OK
   
   
   
   
   
   
   
   
   
   
   
   
   
   • Click on scatter-loading option and browse to the scatter file of your stock rom choose MTxxxx_android.txt (scatter.txt).
   
   
   
   
   
   
   
   
   
   
   • Dont touch any options, Keep the original setting (In case you want to format device before flash press choose format+download but it'snt recommanded because you will be ended with an EMEI null)
   • If you phone is alive and has a software issue (contain virus, Stuck on logo, apps setting problem, blink, or not work as expected) I advise you to Uncheck Preloader as a precaution. On contarary check all pertitions if you have a boot problem (you phone does'nt boot when you try to power on it).
                                  
   
   
   
   • Once you are done with everything, click on the download button at the top of the software.
   
   
   
   
   
   
   
   Stop should now be prominent while other options should be grayed out
   
   
   
   
   • Connect your switched off phone with battery inside to PC via Usb cable
   • A progressbar should start running
   
   
   
   
   
   • In the end of an success flash process, a box should show up with green OK symbol inside
   
   
   
   
   
   • Disconnect the phone, remove the battery, slot it back in then power the phone.

ENJOY.